SPECIFICATION SHEET FOR 1985 581cc IKUZAWA HONDA
|
Description
|
Specification
|
Supplier
|
Rear Wheel
|
RGV250N rear wheel 4x17
|
Breaker
|
Rear wheel sprocket spacer
|
RGV250N
|
Breaker
|
Rear sprockets assorted
|
RGV250N or Renthal alloy
|
Breaker & B&C express
|
Rear Tyre
|
Michelin Pilot Race (soft) 160/60 31 PSI
|
FTW
|
Rear disk
|
RGV250N Stealth after market disc
|
Stealth
|
Rear Caliper
|
Brembo cast twin pot
|
Andover Norton
|
Front Caliper
|
Pretech six pot x 2, anodised blue
|
Pretech
|
Front Tyre
|
Michelin Pilot Race (soft) 120/70 30 PSI
|
FTW
|
Chassis
|
Harris Tubular special build No. HPIK8
|
Harris Engineering
|
Engine
|
XBR500 bottom end/head with XL600R barrel Nos. 100x75 bore x stroke
|
Team Ikuzawa, Tokyo, Japan
|
Cam
|
HRC cam
|
HRC
|
Carburettor stub adaptor
|
AMAL rubber stub adaptor 2036/123
|
Andover Norton
|
Carburettor
|
AMAL smoothbore Series 2000 Mark II. 39.5mm internal diameter Needle 2A-1 middle notch 3rd from top. Slide 4 (Rec. 3) Needle Jet 106. Main Jet 370 for IOM
|
Andover Norton
|
Piston
|
Wiseco for XL600R with enlarged valve cutouts
|
Stan Stephens
|
Front Forks
|
RGV250N USD standard tune
|
Breaker
|
Rear Shock unit
|
Ohlins
|
Harris
|
Chain
|
Reynolds 520 GP (can use equivalent DID/Regina etc)
|
B&C express
|
Front Sprocket
|
15, 16, 17 tooth flat
|
B&C express
|
Oil
|
Morris fully synthetic or equivalent (eg Silkolene Comp 4, Mobil 1) 2.5 litres
|
Any dealer
|
Petrol
|
50/50 mix of AvGas and super unleaded (or 100% super)
|
Petrol station/local airfield
|
Brake pads rear
|
Brembo
|
Main dealer
|
Brake pads front
|
EBC
|
Main dealer
|
Front Wheel
|
RGV250N front 250x17
|
Dymag
|
Spark plug
|
NGK D9EA or equivalent
|
Main dealers
|
Points (if not using electronic ignition)
|
Early mini type with minor modification 39 degree advance
|
Halfords
|
Tappets
|
Inlet 0.004, exhaust 0.005
|
-
|
Camchain
|
One off setup with ratchet tensioner. Put bike on compression and push screwdriver through port at right rear of barrel
|
-
|
Carb jets
|
AMAL genuine jets 320 - 370 sizes
|
Andover Norton
|
Carb rubber
|
43mm genuine AMAL rubber
|
Andover Norton
|
Seat Unit
|
1994 RS250
|
Replica Fairings
|
Fairing
|
TZ250B plus mods
|
Replica Fairings
|
Screen
|
TZ250B
|
Replica Fairings
|
Exhaust
|
One off ‘Invader’ pipes with Invader alloy can
|
www.moonpie.co.uk
|
Exhaust header
|
One off drilled brass header bolts, standard Honda XBR500 header copper gaskets with high temperature Instant Gasket sealant
|
Main dealer
|
Petrol Tank
|
Harris tank skin with Dave Molyneux base
|
Harris, Dave Molyneux
|
Footrests, hangers, gear level, brake lever
|
One off machined alloy
|
SRP Engineering
|
Gear lever connecting rod
|
One off machined steel, enamelled
|
Big 4 Engineering
|
Oil Tank
|
One off tank modified and hooked to frame with JB weld
|
Big 4 Engineering
|
Battery(normal)
|
CB4-LB
|
Main Dealers
|
Battery MF heavy duty sealed
|
Yokohama Y4L-SF
|
Main Dealers
|
Filler cap
|
Aircraft alloy filler - 12 bolt
|
Harris Engineering
|
Rear Brake Master Cylinder
|
Alloy Harris unit
|
Harris Engineering
|
Cables
|
One off - all cables
|
Venhill Engineering
|
Clip ons
|
Race Products 50mm
|
M&P
|
Steering Damper
|
RS250 factory damper
|
HRC
|